![]() casien and calcimine paints), and silicone. Protect the product from moisture during. Weld-Crete® is also used for: bonding setting beds for ceramic tile bonding Portland cement plaster and stucco mixes and to bond to surfaces such as brick, block, tile, marble, metal, glass block, soundly adhered paint (non-soluable in water, i.e. Over interior monolithic concrete, USG Plaster Bonder must be applied before plastering. Use Weld-Crete’s® open time to your advantage in bonding to concrete shear walls when you need a time lapse between application of bonding agent, placement of reinforcement steel, placement of formwork and placement of concrete. Plaster-Weld direct to concrete ceilings and other structural surfaces as shown and specified (the mixing, application and finishing of white coat shall be as specified for regular white finish coat). Weld-Crete®can be “painted on” in a single application 1 hour to 10 days prior to concrete placement. For exterior and interior use, Weld-Crete® will bond new concrete, Portland cement plaster and cementitious mixes to structurally sound concrete floors, walls, columns, beams, steps and ramps. The original chemical concrete bonding agent, Weld-Crete® incorporates polyvinyl acetate homopolymer in a patented formulation. Use Weld-Crete’s® open time to your advantage in bonding to concrete shear walls when you need a time lapse between application of bonding agent, placement of reinforcement steel, placement of formwork and placement of concrete. Applies finishes to various surfaces such as wood, metal, glass, plaster, stucco, wallboard, brick and cement. PHIPPS COMPANY BE LIABLE IN ANY WAY FOR (1) THE CONTENT OF ANY DOCUMENTS, INCLUDING BUT NOT LIMITED TO ANY ERRORS, OMISSIONS OR CHANGES IN ANY DOCUMENTS, OR (2) ANY LOSS OR DAMAGE OF ANY KIND (INCLUDING BUT NOT LIMITED TO ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES, ATTORNEYS’ FEES AND/OR COSTS) ARISING FROM, RELATING TO OR OTHERWISE INCURRED AS A RESULT OF THE USER’S USE OR VIEWING OF SAID DOCUMENTS ACCESSED, DOWNLOADED OR OTHERWISE OBTAINED THROUGH THIS SYSTEM.Weld-Crete® bonds new concrete, stucco, tile setting beds and terrazzo to any structurally sound surface, interior or exterior. ![]() USERS AGREE THAT UNDER NO CIRCUMSTANCE SHALL THE CHAS E. Protect adjacent finish surfaces with masking. Air and surface temperatures must be above freezing during application of Plaster-Weld. Materials Storage: Protect Plaster-Weld from freezing. Portland cement stucco at external corners. Deliver Plaster-Weld to job in original container with seals unbroken and use without reducing. ![]() USERS ARE CAUTIONED TO ALWAYS CONSULT THE ORIGINAL MANUFACTURER DOCUMENTS. Expanded lath, welded wire, or woven wire mesh bent to approximately 90 used to reinforce. PHIPPS COMPANY DOES NOT GUARANTEE THE COMPLETENESS, ACCURACY, QUALITY OR CONTENT OF ANY OF THE DOCUMENTS ACCESSED, DOWNLOADED OR OTHERWISE OBTAINED THROUGH THE SYSTEM, WHICH DOCUMENTS MAY BE AMENDED, CORRECTED OR SUPERSEDED FROM TIME-TO-TIME BY THE MANUFACTURER. ![]() Gardz be sure to determine that the surface is clean. TERMS AND DISCLAIMER: ANY MATERIAL ACCESSED, DOWNLOADED OR OTHERWISE OBTAINED THROUGH THIS SYSTEM IS DONE SO AT THE USER’S DISCRETION AND SOLE RISK. Allow new plaster to cure at least 24 hours before applying Gardz. Weld-Crete is also used for bonding setting beds for ceramic tile and for bonding portland cement plaster and stucco mixes and to bond to such surfaces as. All documents are in pdf format and have been compiled from manufacturer websites. Plaster-Weld® bonds new plaster to any clean, structurally sound, interior surface. Phipps Tech / SDS Documents system is a search service to product information for the Concrete, Finishes, Masonry and Thermal and Moisture Protection Divisions.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |